ដំណើរការរំកិលក្រដាសអាលុយមីញ៉ូម និងលក្ខណៈ

នៅក្នុងការផលិតនៃ foil ទ្វេ, ការរំកិលក្រដាសអាលុយមីញ៉ូមចែកចេញជាបីដំណើរការ: រមៀលរដុប, ការរំកិលកម្រិតមធ្យម, និងបញ្ចប់ការរមៀល. តាមទស្សនៈបច្ចេកវិទ្យា, វាអាចត្រូវបានបែងចែកប្រហែលពីកម្រាស់នៃច្រកចេញវិល. វិធីសាស្រ្តទូទៅគឺថាកម្រាស់នៃការចេញគឺធំជាងឬស្មើនឹង 0.05mm គឺជាការរមូររដុប។, កម្រាស់នៃច្រកចេញគឺនៅចន្លោះ 0.013 និង 0.05 is intermediate rolling, and the single finished product and double rolled product with the exit thickness less than 0.013mm are finished rolling. The characteristics of rough rolling are similar to the rolling characteristics of aluminum plate and strip. The thickness control mainly depends on the rolling force and post tension. The thickness of the rough rolling is very small, and its rolling characteristics are completely different from the rolling of aluminum plate and strip. It has aluminum foil rolling. The particularity of, its characteristics mainly include the following aspects:

(1) Aluminum strip rolling. To make the aluminum strip thinner mainly depends on the rolling force, so the automatic thickness control method is the constant roll gap as the main control method of the AGC. Even if the rolling force changes, the roll gap can be adjusted at any time to keep the roll gap at a certain value to obtain the thickness. Consistent plate and strip. When aluminum foil is rolled to medium-finish rolling, because the thickness of aluminum foil is extremely thin, the rolling force is increased during rolling, which makes it easier for the roll to produce elastic deformation than the material being rolled. The elastic flattening of the roll is not possible. Ignored, the elastic rolling and flattening of the rolls determines that in aluminum foil rolling, the rolling force can no longer play the same role as the rolled plate. Aluminum foil rolling is generally roll-free rolling under constant pressure conditions to adjust the thickness of the aluminum foil. Mainly depends on the adjusted tension and rolling speed. To

(2) Stack rolling. For ultra-thin aluminum foil with a thickness of less than 0.012mm (កម្រាស់គឺទាក់ទងទៅនឹងអង្កត់ផ្ចិតនៃរមៀលការងារ), due to the elastic flattening of the roll, it is very difficult to use a single-sheet rolling method, so the double rolling method is adopted, that is The method of adding lubricating oil between two aluminum foils and then rolling them together (ហៅផងដែរថា stack rolling). Stack rolling can not only produce ultra-thin aluminum foil that cannot be produced by single rolling, but also reduce the number of breaks and increase labor productivity. Using this process, single-sided smooth aluminum foil of 0.006mm to 0.03mm can be mass-produced. To

(3) Speed effect. In the process of aluminum foil rolling, the phenomenon that the thickness of the foil thins with the rise of the rolling system is called the speed effect. The explanation of the speed effect mechanism still needs in-depth study. The reasons for the speed effect are generally believed to have the following three aspects:

The friction state between the work roll and the rolled material changes. As the rolling speed increases, the amount of lubricating oil introduced increases, so that the lubrication state between the roll and the rolled material changes. The friction coefficient decreases, the oil film becomes thicker, and the thickness of the lead foil decreases accordingly.
Changes in the rolling mill itself. In rolling mills with cylindrical bearings, as the rolling speed increases, the roll necks will float in the bearings, so that the two rolls that interact with each other under load will move toward each other.
The material is softened by the processing of the L system. The rolling speed of the high-speed aluminum foil rolling mill is very high. As the rolling speed increases, the temperature of the rolling deformation zone increases. According to calculations, the metal temperature in the deformation zone can rise to 200°C, which is equivalent to an intermediate recovery annealing. The processing softening phenomenon of rolled materials.